Table of Contents

How To Make Led Propeller Clock | Arduino Projects

How To Make Led Propeller

Led propeller clock बनाने के लिए हमे कुछ चीजों की ज़रूरत पड़ेगी आइये देखते है।

Components :-

Arduino Nano , Buy Arduino Nano At Low Price ₹538
10K Resistor 4pc
220 ohms Resistor 17 pc
Red LED 11 pc
Green Led 5 pc
Blue LED 1 pc
Hall Effect Sensor 3144 , 1 pc
IR Receiver 1 pc
IR Transmitter 1 pc
Motor 1 pc
3.7 volt battery 1 pc

Buy Esp 8266 Board

ये है Diagram आप इसे देख कर बहुत आसानी से बना सकते है और नीचे में कोड दे रहा हूँ उसे आप कॉपी कर सकते है।

How To Make Led Propeller

बनाने के बाद आपको अपने Arduino Nano को programme करना है।

How To Programme Arduino Nano ?

Arduino को प्रोग्राम आप अपने मोबाइल से भी कर सकते है और कंप्यूटर से भी कर सकते है।

Download Winzo App And Get ₹50 instantly

How To Programme Arduino With Smartphone ?

अपने मोबाइल से प्रोग्राम करने के लिए आपको Play Store से एक app डाउनलोड करना है जिसका नाम है Arduino Droid Download करने के बाद आपको app ओपन करना है फिर उसमें boards में जाना है और arduino nano को सेलेक्ट कर देना है फिर आपको एक OTG लेना है और arduino nano के केबल से अपने फ़ोन को कनेक्ट करना है।

How To Make Led Propeller

फिर जो मैंने कोड दिया है उसे आपको कॉपी करना है और app में पेस्ट कर देना है फिर आपको Compile करना है जब Complile कम्पलीट हो जाये तो आपको upload पर क्लिक करना है । आपका कोड upload हो जाएगा।

Copy The Code

/ inventions with taufik // 22-08-2019   PropellerClockRpmBatteryStatusDisplay unsigned int x,j,n,k,d,ADCvalue,nm,dl; unsigned long previousTime,rpm,tc,to = 0; long v; byte hours = 12;     // set Hours byte minutes = 15;   // set minutes byte seconds = 00;  // set seconds int i,m,f,f1,val = 0; byte a,c; char s; const PROGMEM  unsigned char data[]={0x3f,0x23,0x23,0x3f,0x01,0x13,0x3f,0x03,0x2f,0x2b,0x2b,0x3b,0x2b,0x2b,0x2b,0x3f,0x39,0x09,0x09,0x3f,0x3b,0x2b,0x2b,0x2f,0x3f,0x2b,0x2b,0x2f,0x21,0x27,0x29,0x31,0x3f,0x2b,0x2b,0x3f,0x3b,0x2b,0x2b,0x3f,0x00,0x00,0x15,0x00,0x01,0x01,0x3f,0x29,0x2d,0x13,0x01,0x3f,0x29,0x29,0x11,0x01,0x3f,0x11,0x09,0x11,0x3f,0x39,0x05,0x03,0x05,0x39,0x1F,0x11,0x11,0x00,0x1F,0x01,0x01,0x01,0x1f,0x11,0x11,0x1F,0x1F,0x11,0x11,0x00,0x1F,0x04,0x0A,0x11}; void setup() {   DDRD = 0xF8;   DDRB = 0xFF;   DDRC = 0xFE;   PORTC = 0x01;    PORTD = 0x07;   PORTB = 0x00;    if(hours == 12)   hours = 0;   attachInterrupt(0, usdl, RISING);       } void loop() { while(m == 0) {   while(bit_is_clear(PIND, 2)) { }   k=45;   n=0;   while(n < 60)   {        ADCvalue = analogRead(A7);   if(ADCvalue < 500)   {   minutes = k;   seconds = 0;   }   ADCvalue = analogRead(A6);   if(ADCvalue < 500)   {   hours = k/5;   seconds = 0;   }   PORTC |= (1<<5);   if ((k==0) || (k==5) || (k==10) || (k==15) || (k==20) || (k==25) || (k==30) || (k==35) || (k==40) || (k==45) || (k==50) || (k==55))   {   PORTC |= (1<<4);   PORTC |= (1<<3);    }   if ((k==0) || (k==15) || (k==30) || (k==45))   {   PORTC |= (1<<2);   PORTC |= (1<<1);       }   if(k == hours*5 – 1)   PORTD |= (1<<7);   if((k == hours*5) || (( k == 0 ) && (hours == 0)))   {   PORTB |= (1<<5);       PORTD |= (1<<3);   PORTD |= (1<<4);   PORTD |= (1<<5);   PORTD |= (1<<6);   PORTD |= (1<<7);   PORTB |= (1<<0);   }   if(k == hours*5 + 1)   PORTD |= (1<<7);   if((k == 59) && (hours*5 == 0))   PORTD |= (1<<7);    if(k == minutes-1)   PORTB |= (1<<1);   if(k == minutes)   {   PORTB |= (1<<5);       PORTD |= (1<<3);   PORTD |= (1<<4);   PORTD |= (1<<5);   PORTD |= (1<<6);   PORTD |= (1<<7);   PORTB |= (1<<0);   PORTB |= (1<<1);   PORTB |= (1<<2);       }   if(k == minutes+1)   PORTB |= (1<<1);   if((k == 0) && (minutes == 59))   PORTB |= (1<<1);   if((k == 59) && (minutes == 0))   PORTB |= (1<<1);   if(k == seconds-1)   PORTB |= (1<<3);    if(k == seconds)   {   PORTB |= (1<<5);      PORTD |= (1<<3);   PORTD |= (1<<4);   PORTD |= (1<<5);   PORTD |= (1<<6);   PORTD |= (1<<7);   PORTB |= (1<<0);   PORTB |= (1<<1);   PORTB |= (1<<2);   PORTB |= (1<<3);   PORTB |= (1<<4);     }   if(k == seconds+1)   PORTB |= (1<<3);   if((k == 0) && (seconds == 59))   PORTB |= (1<<3);   if((k == 59) && (seconds == 0))   PORTB |= (1<<3);        delayMicroseconds(dl);   PORTD = 0x07;   PORTB = 0x00;   PORTC = 0x01;   PORTB |= (1<<5);   delayMicroseconds(dl/50);   PORTB &= ~(1<<5);       delayMicroseconds(dl*4);   n++;   k++;   if(k == 60)   k=0;   }   while(bit_is_set(PIND, 2))   {   }     } while(m == 1)   {   while(bit_is_clear(PIND, 2)) { }   ADMUX = _BV(REFS0) | _BV(MUX3) | _BV(MUX2) | _BV(MUX1);   delay(2);   ADCSRA |= _BV(ADSC);   while (bit_is_set(ADCSRA,ADSC));   v = ADCL;   v |= ADCH<<8;   v = 1125300L / v;   nm = v/1000;   nm = nm%10;   nD();   delayMicroseconds(dl*4);   PORTC = 0x03;   delayMicroseconds(dl);    PORTC = 0x01;   delayMicroseconds(dl*6);   nm = v/100;   nm = nm%10;   nD();   delayMicroseconds(dl*2);    nm = v/10;   nm = nm%10;   nD();   delayMicroseconds(dl*2);     i = 0;   while(i < 5) {   PORTC = (pgm_read_byte(&(data+61)[i]));   delayMicroseconds(dl);    PORTC = 0x01;   delayMicroseconds(dl*2);   i++; }   i = 0;   while(i < 10) {   delayMicroseconds(dl);    i++; }                rpm = (100000000/tc)*60;   nm = rpm/100000;   nm = nm%10;   if(nm !=0)   nD();   delayMicroseconds(dl*2);   nm = rpm/10000;   nm = nm%10;   nD();   delayMicroseconds(dl*2);    nm = rpm/1000;   nm = nm%10;   nD();   delayMicroseconds(dl*2);        nm = rpm/100;   nm = nm%10;   nD();      delayMicroseconds(dl*2);   i = 0;   while(i < 17) {   PORTC = (pgm_read_byte(&(data+44)[i]));   delayMicroseconds(dl);    PORTC = 0x01;   delayMicroseconds(dl*2);   i++; }    while(i < 50) {   delayMicroseconds(dl);    i++; }       nm = seconds;   nm = nm%10;   nmDB();   delayMicroseconds(dl*2);   nm = seconds/10;   nm = nm%10;   x=4;   nmDB2();   delayMicroseconds(dl*2);   nm = 10;   x=3;   nmDB2();   delayMicroseconds(dl*2);    nm = minutes;   nm = nm%10;   x=2;   nmDB2();   delayMicroseconds(dl*2);   nm = minutes/10;   nm = nm%10;   x=1;   nmDB2();   delayMicroseconds(dl*2);   nm = 10;   x=0;   nmDB2();   delayMicroseconds(dl*2);    nm = hours;   if(nm == 0)   nm = 12;   nm = nm%10;   nmDB();   delayMicroseconds(dl*2);      nm = hours;   if(nm == 0)   nm = 12;   nm=nm/10;    nm = nm%10;   nmDB();      while(bit_is_set(PIND, 2))   {   } } } void nD() {   j=nm*4;   i = 0;   while(i < 4) { PORTC = (pgm_read_byte(&(data+j)[i])); delayMicroseconds(dl); PORTC = 0x01; delayMicroseconds(dl*2); i++; } } void nmDB2() { j=nm*4; x = x*4; i = 3; while(i >= 0) {   c = (pgm_read_byte(&(data+j)[i]));   s=0;   for(a = 0; a < 8; a++){     s <<= 1; s |= c & 1; c >>= 1;   }   s >>= 1;   PORTC = s;   c = (pgm_read_byte(&(data+66+x)[i]));    s=0;   for(a = 0; a < 8; a++){     s <<= 1; s |= c & 1; c >>= 1;   }   PORTB = s >>= 3;   PORTB &= ~(1<<5); delayMicroseconds(dl); PORTC = 0x01; PORTB = 0x00; PORTD = 0x04; delayMicroseconds(dl*2); i–; } } void nmDB() { j=nm*4; i = 3; while(i >= 0) {   c = (pgm_read_byte(&(data+j)[i]));   s=0;   for(a = 0; a < 8; a++){     s <<= 1; s |= c & 1; c >>= 1;   }   s >>= 1;   PORTC = s;   delayMicroseconds(dl);    PORTC = 0x01;   delayMicroseconds(dl*2);   i–; } }    void usdl() {      f = 0;   n = 0;   tc = micros()-to;   to = micros();   f = 1;   if(m == 0)   dl = tc/410;   else   dl = tc/400;       if (millis() >= (previousTime))   {   previousTime = previousTime + 1000;   seconds = seconds+1;   if (seconds == 60)   {   seconds = 0;   minutes = minutes+1;   }   if (minutes == 60)   {   minutes = 0;   hours = hours+1;   }   if (hours == 12)   {   hours = 0;   }   }   if(bit_is_clear(PINC, 0))   m = 1;   else   m = 0; }

How To Programme Arduino With Computer ?

कंप्यूटर से भी प्रोग्राम करना बहुत आसान है आपको अपने कंप्यूटर में एक सॉफ्टवेयर डाउनलोड करना है जिसका नाम है Arduino IDE फिर आपको same process करना है जो मैंने ऊपर में बताया है।

How To Make Led Propeller

अब हमें मोटर ले लेना है और उसे एक प्लाई बोर्ड में बीच मे लगा देना है प्लाई बोर्ड में आपको ब्लैक पेपर चिपका देना है और एक छोटा सा मैगनेट लगाना है आप मेरे वीडियो में देख सकते है मैने कैसे लगाया है।

हमारा प्रोजेक्ट कम्पलीट हो गया।